UK Supplier of Motorcycle Parts & Spares · Nottingham
PP Pattern PartsMotorcycle spares since 2001
Close-up of polished chrome motorcycle engine components arranged on a dark workshop bench, deep navy and steel tones with warm orange workshop lighting.
★ ★ ★ ★ ★ Trusted UK Parts Supplier
FREE UK Delivery on all mainland orders over £100 | Over 30,000 motorbike spares in stock | Open Mon–Fri, 9am–5.30pm

Installing motorcycle frame sliders for real protection

Motorcycle frame sliders are small sacrificial guards fixed to the motorcycle’s frame or engine mounting points. Their job is to take a glancing hit during a low-speed tip-over and let the bike slide rather than gouge the metal. They can save repair costs after a fall in a car park, but they do not protect the rider or guarantee survival of a faster crash.

Installing motorcycle frame sliders for protection is usually straightforward once the correct model, hardware and clearance requirements have been identified. The work calls for a securely supported bike, basic hand tools, a torque wrench and careful checks around the steering, chain, exhaust and suspension. Spend time on fitment: a misaligned or overtightened slider can cause a problem more serious than the damage it was meant to prevent.

Choose the correct slider for your motorcycle

Begin with the bike’s exact make, model, year and variant. Some frame sliders use existing crash-bobbin holes, while others require supplied bolts, sleeves or spacers. A similar-looking motorcycle may use different hardware, so never transfer a torque figure or fastener without confirming compatibility. The installation instructions should identify every mounting point and the parts that must be removed.

Choose a kit designed for the frame location you want to protect, whether that is the front frame, engine rail or lower rear mounting point. Nylon sliders are sacrificial and often replaceable after an impact, while alloy sliders may be tougher but can damage the frame if they dig into it. At Pattern Parts, use the model and year information rather than selecting by appearance, and check current delivery information for destinations, dispatch times and charges to Australia before ordering.

Prepare the motorcycle and work area

Work on a level surface with the engine cold, the motorcycle fully supported and the transmission secured according to its owner’s manual. A paddock stand and suitable rear support are often more appropriate than relying on a side stand. Gather the tools listed in the kit instructions, usually metric sockets or Allen keys, spanners, a torque wrench, a clean cloth and a small container for the hardware.

Inspect the exposed mounting holes and surrounding frame for cracks, stripped threads or previous repairs. Clean away road grime with a degreaser and dry the area thoroughly. Pay particular attention to corrosion near coastal suburbs, where salt can undermine a fastener that looked sound when the slider was first installed. Use thread-locking compound only if the manufacturer specifically permits it.

Fit the mounting hardware correctly

Remove only the fasteners identified in the instructions, supporting each slider as the final bolt comes out so it does not fall onto the engine or workstand. If the original hardware is reused, inspect its threads and washer faces; the kit may specify stronger replacement bolts instead. Keep components from each side separate if the left and right sliders differ.

Fit the supplied sleeve or spacer through the slider and into the mounting point, making sure it seats squarely without force. Start the fastener by hand and confirm that the slider can still rotate slightly where the design allows it. If it must sit perfectly still, the spacer, washer order or bolt length may be incorrect. Never substitute a longer bolt, as it could reach an oil gallery, water passage or moving internal component.

Align the slider and tighten the fasteners

With the hardware seated, turn the handlebars fully left and right while checking the slider against the fork, fairing and adjacent frame. The slider should sit parallel to the frame at normal steering angles and should not pull against anything. Feel for contact as the bars move through their complete travel rather than relying only on a visual inspection.

Tighten the fasteners in the sequence given by the manufacturer, usually working from the inner mounting point outward. Set the torque wrench to the specified value and pull until it clicks; do not add a cosmetic turn afterward. If no torque figure is provided, obtain one for the exact fastener. Repeat the alignment check after final tightening, and inspect beneath the motorcycle with the suspension compressed.

Check steering, clearance and surrounding parts

Check the chain and sprocket on the left, the exhaust and footrest on the right, plus brake hoses, electrical leads, the radiator and the tyre. A slider must never foul a moving or hot component. Turn the steering through full lock in both directions, including the direction normally encountered in Australia’s left-hand traffic, and confirm that the brake and clutch controls still operate freely.

Remove bodywork only if the instructions require it, using the correct tools and retaining every clip and washer. Fairing panels can catch on the slider, while pinched wiring may fail later without making noise during installation. Check ground clearance with the motorcycle carrying its normal rider load. This is especially important on broken city streets and corrugated unsealed roads around Alice Springs, where repeated impacts can loosen a mount that appeared sound during a static inspection.

Test, inspect and maintain the protection

Before the first ride, walk around the motorcycle and repeat the clearance checks with the engine running. A short, low-speed shakedown can reveal chain rub, steering interference or a fastener that has moved. Follow any break-in distance specified by the slider maker, then recheck the mounting bolts and torque after the initial ride and again after a few hundred kilometres.

After a low-speed knockdown, inspect the slider even if the motorcycle appears undamaged. Look for a flattened mounting face, deep scoring, a cracked insert or a bent bracket. Replaceable nylon sliders are designed to be sacrificed, and a distorted one should not be reused. Wash road film away with mild soap, avoid harsh solvents and dry the fasteners to prevent corrosion. Red dust inland, salt air along the Queensland coast and strong summer UV can shorten the life of plastic or unfinished metal.

Avoid common mistakes before riding

The most common errors are using hardware from the wrong model, omitting a spacer, overtightening an unfamiliar bolt and failing to check full steering lock. Another mistake is treating frame sliders as general crash armour. They primarily help during low-speed tip-over events and cannot guarantee that an engine, exhaust or fuel system will survive a faster collision.

Use a repeatable pre-ride check: confirm the fasteners, inspect for rubbing, operate the steering and brakes, and ensure the slider has correct ground clearance. Keep the instructions, receipts and fitment details with the motorcycle’s service records, particularly for an Australian rego or insurance question. When comparing another retailer, check model fitment, included hardware and torque guidance with the same scrutiny; a specialist source such as Joker Racing can provide a useful cross-check.


Get the exact model and year, order the complete fitting kit, and follow its specified torque and clearance procedure before riding. A correctly fitted slider should disappear in normal use while standing ready for the next low-speed tip-over, whether that means filtering through Sydney traffic, threading a Melbourne laneway or heading across red-dirt country on the next arvo ride.